Incoloy Alloy 825 Forgings

Short Description:

Specifications of Incoloy Alloy 825 Forgings: Specifications ASTM B564 / ASME SB564 Flat bar blocks up to 27" width and 15,000 lbs Cylinders and sleeves up to 50" maximum O.D. and 65" maximum length Discs and hubs up to 50" diameter and 20,000 lbs Rolled, hand forged or mandrel forged rings up to 84" maximum O.D. and 40" maximum length Rounds, shafts and step shafts up…

Grade:: Incoloy Alloy 825
Standard:: ASTM B564 / ASME SB564
Surface:: Mill finish, pickled, polished, or as required
Diameter:: Not applicable

Send email to us

Product Detail

Product Tags

Specifications of Incoloy Alloy 825 Forgings:

Specifications	ASTM B564 / ASME SB564
Flat bar blocks	up to 27" width and 15,000 lbs
Cylinders and sleeves	up to 50" maximum O.D. and 65" maximum length
Discs and hubs	up to 50" diameter and 20,000 lbs
Rolled, hand forged or mandrel forged rings	up to 84" maximum O.D. and 40" maximum length
Rounds, shafts and step shafts	up to 144" maximum length and 20,000 lbs.

Other Type Of Incoloy Alloy 825 Forgings:

Equivalent Grades Of Incoloy Alloy 825 Forgings:

STANDARD	WERKSTOFF NR.	UNS	BA	JIS	GOST	EN	OR
825	2.4858	N08825	NA21	NCF 825	ХН65МВУ	NiCr22Mo9Nb	ЭИ602

CHEMICAL COMPOSITION OF Hastelloy C276 Forgings:

Grade	C	Mn	Si	S	Fe	Ni	Cr	Al	Ti
825	0.10	0.50	0.50	0.015	5.0	58.0	20.0-23.0	0.40	0.40

Incoloy Alloy 825 Forgings Mechanical Properties:

Density	Melting Point	Tensile Strength	Yield Strength	Elongation
8.4 g/cm3	1350 °C (2460 °F)	Psi – 135000 , MPa – 930	Psi – 75,000 , MPa – 517	42.5%

SASA ALLOY'S Manufacturing Process for Forged Bars and rings:

The square/flat bars are made from ingots and are processed after giving required reduction ratio and discarding hot top and bottom for homogeneity. They are either processed by hot rolling or hot forging. These bars are further heat treated as per customer requirements by any one of the following processes

1.Annealing 2.Normalizing 3.Stress Relieving 4.Quenching and Tempering 5.Spheroidizing Annealing

Quality Check of Forged:

Following checks are conducted in bars/rings/step shafts and reported in the TEST CERTIFICATE as per customer requirement. 1.Surface inspection is carried out of each bar end to end 2.Positive Material Identification using XRF to certify in process chemistry of each bar 3.100% dimensional verification using calibrated verniers and Go No-4.Go gauges 5.Step down testing 6.Upset forging test 7.NMIR (Non metallic inclusion rating) 8.Macrostructure testing 9.Microstructure phase analysis 10.Grain Size 11.Ultrasonic Testing for internal defects 12.Radioactivity test 13.Gas analysis (O, N, H)

Why Choose Us:

Packing:

1. Packing is quite important especially in a case of international shipments in which consignment pass through various channels to reach the ultimate destination, so we put special concern regarding packaging.

2. Sasa alloy’s pack our goods in numerous ways based on the products. We pack our products in multiple ways, such as,