Nimonic 75 UNS N06075 Sheet and Plate is supplied for oxidation-resistant service and fabricated hot-section components. Material selection, dimensions, heat treatment, testing and documentation are reviewed against the purchase specification and end-use conditions.
Nimonic 75 UNS N06075 Sheet and Plate Specification
| Alloy |
Nimonic grade |
| UNS / W.Nr. |
N06075 / 2.4630 |
| Reference standards |
ASTM B463 / BS HR 5 or customer-specified equivalent |
| Product forms |
Cold-rolled sheet, hot-rolled plate and cut-to-size blanks |
| Supply condition |
Solution-treated or other condition required by the governing specification |
| Dimensions |
Thickness, width and length confirmed with the quotation |
| Surface |
Pickled, descaled, bright or customer-specified finish |
| Documentation |
EN 10204 3.1 material certificate and requested inspection records |
Available Forms and Processing
| Stock and production |
Sheet, plate, strip and precision-cut blanks subject to availability |
| Cutting |
Shearing, sawing, laser, waterjet or plasma selected by thickness and tolerance |
| Forming |
Bending and forming procedure must consider work hardening and condition |
| Welding |
Qualified procedures and matching filler selection should follow the service requirement |
| Edge / surface |
Mill edge, cut edge, deburred edge and protective-film options by agreement |
Equivalent Designations
| UNS |
N06075 |
| Werkstoff |
2.4630 |
| Trade designation |
Nimonic grade stated in the product title |
| Important note |
Designations are cross-references only; compliance is determined by the ordered standard, chemistry, mechanical properties and condition. |
Typical Chemical Composition
| Nominal composition |
Ni balance; Cr 18.0–21.0%; Fe ≤5.0%; Ti 0.2–0.6%; C 0.08–0.15% |
| Verification |
Final acceptance shall use the heat analysis and limits in the ordered material specification. |
| Traceability |
Heat number is linked to the material certificate and package identification. |
Typical Physical Properties
| Density |
8.37 g/cm³ |
| Property basis |
Published typical values are guidance values and are not guaranteed acceptance criteria. |
| Design use |
Engineering design should use temperature-dependent data from the applicable specification or approved material source. |
Request a Quote
Mechanical Properties and Heat Treatment
| Condition |
Properties depend on product thickness, solution treatment and any precipitation-hardening cycle. |
| Acceptance |
Tensile, yield, elongation and hardness requirements follow the purchase specification. |
| Heat treatment |
Furnace control, temperature uniformity, cooling practice and batch records should be agreed where critical. |
| Sampling |
Test direction, location and frequency follow the governing standard or approved inspection plan. |
Fabrication Guidance
| Cold forming |
Allow for work hardening, bend radius and intermediate annealing when required. |
| Machining |
Use rigid tooling, positive feeds and suitable coolant; avoid dwell that can work-harden the surface. |
| Welding |
Keep joint surfaces clean and use qualified procedures appropriate to the alloy and service. |
| Post-fabrication |
Remove contamination and verify dimensions, surface and required NDT after processing. |
Inspection and Quality Documentation
| Material certificate |
EN 10204 3.1 or agreed alternative |
| Identification |
Grade, heat number, size and package marks |
| Optional testing |
PMI, UT, PT, dimensional report, hardness or third-party inspection by agreement |
| Quotation inputs |
Standard, size, quantity, condition, tolerance, testing, documentation and delivery destination |
Applications
Typical procurement enquiries include furnace components, heat-treatment fixtures, gas-turbine sheet fabrications and industrial thermal equipment. Application suitability must be confirmed by the purchaser’s engineer for temperature, atmosphere, stress and fabrication route.
Request a Quote
Nimonic 75 UNS N06075 Sheet and Plate Packaging
Sheets and plates are separated and protected as required, secured on pallets or in export cases, and marked so package identification remains linked to the material documentation.
Procurement Confirmation
| Please provide |
Grade and standard; dimensions; quantity; condition; tolerance and surface; test and certificate requirements; destination and requested delivery date |
| Quotation review |
Availability, production route, technical compliance, packing and lead time are confirmed before acceptance. |
Request a Quote
Previous: ASTM B575 Hastelloy C-2000 UNS N06200 Sheet and Plate
Next: Nimonic 81 UNS N07081 Sheet and Plate
